Nucleo STM32F446 - F5UII V2 Interface

[do3lk]

Hello,

I have a Problem to Build new Firmware for STM32F446 on Arduino IDE.
The Arduino IDE Say Error:
In file included from C:\Users\MV\Desktop\MMDVM-master\MMDVM\MMDVM.ino:21: C:\Users\MV\Desktop\MMDVM-master\MMDVM\Globals.h:38:2: error: #error "Unknown processor type" 38 | #error "Unknown processor type" | ^~~~~ In file included from C:\Users\MV\Desktop\MMDVM-master\MMDVM\SerialPort.h:24, from C:\Users\MV\Desktop\MMDVM-master\MMDVM\Globals.h:73: C:\Users\MV\Desktop\MMDVM-master\MMDVM\RingBuffer.h:39:2: error: #error "Unknown processor type"

My Config.h

`#if !defined(CONFIG_H)
#define CONFIG_H

// Allow for the selection of which modes to compile into the firmware. This is particularly useful for processors
// which have limited code space and processing power.

// Enable D-Star support.
#define MODE_DSTAR

// Enable DMR support.
#define MODE_DMR

// Enable System Fusion support.
//#define MODE_YSF

// Enable P25 phase 1 support.
//#define MODE_P25

// Enable NXDN support, the boxcar filter sometimes improves the performance of NXDN receive on some systems.
//#define MODE_NXDN
//#define USE_NXDN_BOXCAR

// Enable POCSAG support.
// #define MODE_POCSAG

// Enable FM support.
//#define MODE_FM

// For 12.288 MHz
#define EXTERNAL_OSC 12288000

// Select a baud rate for host communication. The faster speeds are needed for external FM to work.
#define SERIAL_SPEED 115200 // Suitable for most older boards (Arduino Due, etc). External FM will NOT work with this!
// #define SERIAL_SPEED 230400 // Only works on newer boards like fast M4, M7, Teensy 3.x. External FM might work with this
//#define SERIAL_SPEED 460800 // Only works on newer boards like fast M4, M7, Teensy 3.x. External FM should work with this
//#define SERIAL_SPEED 500000 // Used with newer boards and Armbian on AllWinner SOCs (H2, H3) that do not support 460800

// Use pins to output the current mode via LEDs
#define MODE_LEDS

// For the original Arduino Due pin layout
// #define ARDUINO_DUE_PAPA

// For the ZUM V1.0 and V1.0.1 boards pin layout
// #define ARDUINO_DUE_ZUM_V10

// For the SP8NTH board
//#define ARDUINO_DUE_NTH

// For ST Nucleo-64 STM32F446RE board
#define STM32F4_NUCLEO_MORPHO_HEADER
// #define STM32F4_NUCLEO_ARDUINO_HEADER

// Use separate mode pins to switch external channel/filters/bandwidth for example
#define MODE_PINS

// For the VK6MST Pi3 Shield communicating over i2c. i2c address & speed defined in i2cTeensy.cpp
// #define VK6MST_TEENSY_PI3_SHIELD_I2C

// Pass RSSI information to the host
#define SEND_RSSI_DATA

// Use the modem as a serial repeater for Nextion displays
#define SERIAL_REPEATER

// Set the baud rate of the modem serial repeater for Nextion displays
//#define SERIAL_REPEATER_BAUD_RATE 9600

// Use the modem as an I2C repeater for OLED displays
// #define I2C_REPEATER

// To reduce CPU load, you can remove the DC blocker by commenting out the next line
#define USE_DCBLOCKER

// Constant Service LED once repeater is running
// Do not use if employing an external hardware watchdog
// #define CONSTANT_SRV_LED

// Use the YSF and P25 LEDs for NXDN
// #define USE_ALTERNATE_NXDN_LEDS

// Use the D-Star and DMR LEDs for POCSAG
//#define USE_ALTERNATE_POCSAG_LEDS

// Use the D-Star and YSF LEDs for FM
#define USE_ALTERNATE_FM_LEDS

#endif
`